| GS-EDRV100 Revision History | |||
|
Firmware Version |
Boot Loader Version |
Date |
Description of Problems / Additions / Changes |
| 7.0.119 | 17-Aug-2021 |
Fixed a problem that caused the GS-EDRV100 to return an error 144 (0x86) in
the ERM status. This could happen if the ERM100 and the GS-EDRV100 are
powered on at the same time, and the ERM100 is ready before the GS-EDRV100
auto-negotiates the connection to the GS drive over the serial port. |
|
| 7.0.117 | 7.0.3 | 30-Nov-2020 |
Fixed a problem that would not allow the DIP switches to set an address
above 31. |
| 7.0.111 | 7.0.3 | 3-Jun-2020 |
This is the minimum firmware and boot loader versions required for
GS-EDRV100 with Rev 7A hardware.
Requires the use of
NetEdit v3.17e or later. |
| 6.0.9 | 17-Aug-2021 |
Fixed a problem that caused the GS-EDRV100 to return an error 144 (0x86) in
the ERM status. This could happen if the ERM100 and the GS-EDRV100 are
powered on at the same time, and the ERM100 is ready before the GS-EDRV100
auto-negotiates the connection to the GS drive over the serial port. |
|
| 6.0.3 | 23-May-2018 |
Added ability to disable using port 502 for Modbus/TCP and specify a range
of alternate port numbers to use for Modbus/TCP.
Configuring this option requires the use of
NetEdit v3.16 or later. |
|
| 6.0.2 | 19-Mar-2018 |
Added support for the DURApulse GS4 drive. In previous versions of the firmware, the GS-EDRV100 would
use an auto-baud process to match what the drive's serial port setting, then reconfigure
the drive's serial port to 19200, 8,Odd,1,RTU, then run the auto-baud
process again to match those new
settings. In this version, if the drive's baud rate is lower than 19200, it
will continue to operate as before, but if the drive's port is set to a baud
rate higher than 19200, the GS-EDRV100 will leave it at the higher baud
rate. |
|
| 5.0.258 | 07-Apr-2017 |
The GS-EDRV100 will now read the firmware version of the GS1,
GS2 or GS3 to determine the parameter set that will be accessed. This
removes the need to use specific versions of the GS-EDRV100 firmware with
specific versions of GS1, GS2 or GS3 firmware revisions - requires GS1, GS2
or GS3 firmware version 1.04 or greater. |
|
| 5.0.255 | 29-Apr-2014 |
Fixed a problem where the Name and/or Description would not
show up properly in Do-more Designer's Ethernet I/O Slave configuration
page. |
|
| 5.0.251 | 23-Jan-2014 |
Fixed a problem that prevented some software packages
(KEPDirect, ThinknDo, etc. ) from being able to write outputs. |
|
| 5.0.249 | 7-Jan-2014 |
For all GSx drives, the value for StatusMonitor1 will now be
read from 0x2100 instead of P6.31. |
|
| 5.0.78 | 31-Dec-2013 |
Fixed a problem where the Ethernet chip was not set to
full-duplex mode. |
|
| 5.0.240 | 2-Dec-2013 |
When the GS-EDRV100 powers up, it reads 9.04 & 9.05 from the GSx drive, then propagates the value in 9.05 to the Ethernet’s watchdog timer value as it’s default. When the DM1E’s Ethernet I/O Master fires up, it will overwrite the Ethernet watchdog timer with a new timeout value that is calculated from the Ethernet I/O Slave Setup screen values: (Poll Rate + (Timeout * (Retrys +1 ) ) ) While in Do-more Mode, using the GSx keypad to change the value in 9.05 will no longer cause that value to overwrite the Ethernet watchdog timeout. When not in Do-more Mode, using the GSx keypad to
change the value is 9.05 will cause the new value to be propagated to the Ethernet side watchdog
timeout value. |
|
| 5.0.233 | 16-Oct-2013 |
f the GS-EDRV100 is being used as an Ethernet I/O Slave
device for a Do-more CPU, the Do-more CPU puts the GS-EDRV100 into 'Do-more
mode' to assist the Ethernet I/O Master function. In Do-more Mode, the
GS-EDRV100 does not respond to NetEdit as it normally would. If the
GS-EDRV100 looses its connection to the Do-more CPU, it will drop out of
Do-more mode to allow normal interaction with NetEdit. |
|
| 5.0.231 | 20-Aug-2013 |
Adds support for new address ranges in GS3 drive running firmware version 1.05 or later (there are no changes if connected to a GS1 or GS2 drive). Note: this
version of the GS-EDRV100 firmware is not approved for use with
DuraPulse (GS3) drives that have firmware versions earlier than v1.05. |
|
| 5.0.229 | 20-Aug-2013 |
Minimum version required for use as an Ethernet I/O Slave for
a Do-more CPU (requires Do-more v1.1) |
|
| 5.0.218 | 5.0.76 | 19-Aug-2011 |
Initial Release of the GS-EDRV100. |